Bullard T4 Transmitter Uživatelský manuál stáhnout pdf

Transmitter for the Bullard T3 and T4

Thermal Imager User Manual

Transmitter - Two Channels

Attaching the Wireless Remote Video Transmitting

Handle to the Bullard T3 and T4:

The Bullard T3 and T4 Thermal Imager can be equipped

with an optional wireless remote transmitter. The

transmitter is housed in a convenient handle. To attach the

handle to the T3 or T4, simply align the handle so that the

handle brackets cradle the T3/T4 just under the display and

the electrical contacts on the handle align with

corresponding contacts on the T3/T4 (Figure 1). Turn the

thumbscrew until tightened and the handle is fully secured.

To disconnect the transmitter handle, loosen the

thumbscrew and remove the handle from the T3/T4.

Using the Wireless Remote Video Transmitting Handle:

The transmitter sends a signal to a remote receiver, which

connects to any TV or VCR. The receiver can be powered by

either a 220 volt AC adapter or a 12 volt DC adapter. The

wireless remote transmitter can be set to transmit on one

of two channels depending on the system you have. This

feature allows incident commanders the opportunity to

monitor multiple Bullard Thermal Imagers being used at

the same site.

Selecting the Transmitting Channel: The Bullard T3/T4

Transmitter can transmit on multiple frequencies. To set

the channel option in your Bullard Thermal Imager, turn

the channel indicator knob on the handle from the Off

position to the appropriate channel. The LED indicator at

the top front portion of the transmitter handle will

illuminate indicating that transmission is occurring.

Selecting the Channel on the Receiving Control Unit:

TThe receiving control unit channel must be set to the

same channel as the thermal imager transmitter being

monitored. Select the channel by pointing the indicator

knob, located on the front of the unit, to the appropriate

channel.

NOTE

The two channel transmitter system designed

for the T3 and T4 use the same technology as

transmitter systems provided with the Bullard

TIx and are therefore compatible with these

systems.

NOTE

The electrical contacts on the T3/T4 that

connect with the transmitter handle may

require periodic cleaning. To clean these

contacts, use soapy water and a non-abrasive

cloth to remove dirt and soot, or a cotton swab

and isopropyl alcohol. Rubbing a pencil eraser

on the contacts is another effective, non-

abrasive means to clean the contacts.

Technical Data

Dimensions . . . . . . . . . . . . . . . . . . 38 x 114 x 127 mm

Weight . . . . . . . . . . . . . . . . . . . . . . 454 g.

Power Requirements . . . . . . . . . . 11 – 14.5 V

Power Consumption . . . . . . . . . . . 250 mA

Power Input . . . . . . . . . . . . . . . . . Coaxial 2.1 mm by 5.5 mm

center-positive connector

Frequency . . . . . . . . . . . . . . . . . . . Corresponds to the laws for

communications equipments of

the respective European state

Video Outputs . . . . . . . . . . . . . . . .Two 75-ohm 1-Volt P-P

video outputs (female BNC)

Figure 1

ATTENTION!

Important Note: The use of the radio transmission is subject to

geographical restrictions and must be notified by the buyer at

the responsible authority for communications equipments of

the respective country

CAUTION

Your Bullard Wireless Remote Transmitter/Receiver has been

designed to operate in a variety of environments. However,

Bullard recommends protecting the Receiving Control Unit from

high-moisture environments.

Signal quality may vary considerably depending upon location.

Composition and construction of interior walls and barriers will

affect range indoors. Likewise, outdoor operation could be

affected by large metallic objects, structures, fences, and dense

foliage. Repositioning of both transmitter and receiver may be

necessary to optimize performance.

Failure to note this information may affect operation of the

thermal imager.

T3TRANSONLY2E Two-channel Wireless remote transmitter

(Receiving system not included)

Ordering Information

CATALOG NUMBER DESCRIPTION

1 2

Shrnutí obsahu

Strany 1 - Thermal Imager User Manual

Transmitter for the Bullard T3 and T4 Thermal Imager User ManualTransmitter - Two Channels Attaching the Wireless Remote Video TransmittingHandle to t

Strany 2 - Warranty - T3/T4 Transmitter

Příbuzné modely T3 Transmitter

Další dokumenty pro Bezpečnost Bullard T4 Transmitter

Zobrazit dokument Bullard T4 Transmitter Uživatelský manuál

Bullard T4 Transmitter Uživatelský manuál (2 stránky)

Komentáře k této Příručce

Žádné komentáře

Bullard T4 Transmitter Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Bezpečnost Bullard T4 Transmitter. Bullard T4 Transmitter User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely T3 Transmitter

Další dokumenty pro Bezpečnost Bullard T4 Transmitter

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnost Bullard T4 Transmitter