Bullard T3 Glare Shield Uživatelský manuál stáhnout pdf

Americas:

E.D. Bullard Company

1898 Safety Way

Cynthiana, KY 41031-9303

Toll free: 877-BULLARD (285-5273)

Tel: 859-234-6616

Fax: 859-234-8987

www.bullard.com

Europe:

Bullard GmbH

Lilienthalstrasse 12

53424 Remagen • Germany

Tel: +49-2642 999980

Fax: +49-2642 9999829

www.bullardextrem.com

Asia-Paciﬁc:

Bullard Asia Paciﬁc Pte. Ltd.

LHK Building

701, Sims Drive, #04-03

Singapore 387383

Tel: +65-6745-0556

Fax: +65-6745-5176

www.bullard.com

registered trademark of Bullard.

TacSight is a registed trademark of Bullard.

6050047416D (0212)

ISO 9001

certiﬁed

T3 Series Glare Shield was designed for the Bullard T3 and TacSight Series

Thermal Imagers to enhance viewing in bright, outdoor environments by

eliminating glare.

NOTE

The T3 Series Glare Shield is compatible with MobileLink handheld receivers.

Installation:

1.) Place the Glare Shield in your hands with the clips facing away from your

body and the Bullard embossed logo face up. The nose “notch” should be at

the bottom half of the shield, facing your body.

2.) With your thermal imager lens pointing down and the LCD screen facing up,

tilt the Glare Shield slightly forward (away from the body), allowing the rub-

ber housing to overlap the boot at the top of the camera screen (Figure 1).

3.) Next, slip the clips on each side of the Glare Shield behind the nylon straps

of the camera and gently pull forward and down to create a seal around the

lens. (If you are not able to create this seal, use your finger(s) to properly

seat the Glare Shield) (Figure 2).

4.) To remove, place both hands around the base of the shield and lift

straight out.

Lens Replacement Instructions:

1.) Take the polycarbonate lens and the magnifying lens and place on top of one

another, with the smooth side out. The “rough” side should be sandwiched in

between the lenses (Figure 3).

2.) With the widest portion of the Glare Shield facing you, gently pull the rubber

housing apart and seat the lenses inside the grooves.

Order part number T3GLARESHIELDLENS

Clip Replacement Instructions:

1.) First, make sure you have the replacement part kit T3GLARESHIELDCLIPS.

Using a 3/16” drill bit, drill through the circular area on each clip until the

clip and button detatch from the Glare Shield (Figure 3).

2.) To attach the new clips, place each button on the inside of the Glare Shield,

placing them through the corresponding holes.

3.) Snap each clip to the button to secure.

Order part number T3GLARESHIELDCLIPS

� CAUTION

WHEN USING THE T3 GLARE SHIELD WITH T3 SERIES THERMAL

IMAGERS, TACSIGHT

SERIES THERMAL IMAGERS, OR MOBILELINK

HANDHELD RECEIVER, DO NOT POSITION THE VIEWING DISPLAY

TOWARD THE SUN FOR EXTENDED PERIODS, ESPECIALLY DURING

NON-USE. THE MAGNIFICATION ELEMENTS WITHIN THE GLARE SHIELD

WILL CAUSE DAMAGE TO THE DISPLAY WHEN EXPOSED TO DIRECT

SUNLIGHT. DETACH THE GLARE SHIELD WHEN NOT IN USE. BULLARD

WILL NOT WARRANT REPAIRS RESULTING FROM SUN DAMAGE

INVOLVING THE GLARE SHIELD OPTICS.

T3 Series Glare Shield

Instruction Manual

Figure 1

Figure 2

Figure 3

Clips

Buttons

Lenses

Shrnutí obsahu

Strany 1 - Instruction Manual

Americas:E.D. Bullard Company1898 Safety Way Cynthiana, KY 41031-9303Toll free: 877-BULLARD (285-5273)Tel: 859-234-6616 Fax: 859-234-8987www.bullard

Další dokumenty pro Bezpečnost Bullard T3 Glare Shield

Zobrazit dokument Bullard T3 Glare Shield Uživatelský manuál

Bullard T3 Glare Shield Uživatelský manuál (1 stránky)

Komentáře k této Příručce

Žádné komentáře

Bullard T3 Glare Shield Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Bezpečnost Bullard T3 Glare Shield. Bullard T3 Glare Shield User Manual Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Bezpečnost Bullard T3 Glare Shield

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnost Bullard T3 Glare Shield